Common cosmetic packaging material appearance quality requirements

In order to let the purchasing friends of cosmetics packaging materials understand the quality basis of packaging materials, the editor specially organizes them according to the relevant industry standards introduced by the country, and organizes the inspection and quality standards of cosmetics packaging. This is only for friends purchasing cosmetics packaging materials. When purchasing packaging materials, make a reference to the quality requirements of the product appearance:

1. Commonly used cosmetic packaging materials

In fact, the packaging material classification in the market today does not have most of the specifications, but the editor has sorted it out, and the classification used below is already very comprehensive. If you have overlooked it, you can leave a message and let the editor change it.

a) Bottles (including plastic bottles, glass bottles, etc.);

b) Cover [including outer cover, inner cover, (plug, pad, membrane), etc.];

c) Bags (including paper bags, plastic bags, and composite bags);

d) Hose (including plastic hose, composite hose, metal hose, etc.);

e) Boxes (including plastic boxes, plastic boxes, metal boxes, etc.);

f) Spray cans (including pressure-resistant aluminum cans, iron cans, etc.);

g) Tablet tubes (including lipstick tubes, foundation tubes, mascara tubes, etc.);

h) Cosmetic pencil

i) Nozzle (including pneumatic type and pump type);

j) Outer box (including flower box, plastic seal, middle box, transportation packaging, etc.).

2. Packaging material requirements

The materials used in cosmetic product packaging must be safe and should not cause harm to the human body.

Three, packaging appearance requirements

1. Bottle

The body of the bottle should be stable, the surface should be smooth, and the thickness of the bottle wall should be basically uniform, without obvious scars, deformation, cold bursts and cracks. The bottle mouth should be straight and smooth, no burrs (burrs) should be used, and the thread and bayonet fitting structure should be intact and straight. The fit between the bottle and the cap should be tight, without slippage, looseness, and leakage. The inside and outside of the bottle should be clean.

2 covers

(1) Inner cover: The inner cover should be complete, smooth, clean and not deformed. The inner cap should fit well with the bottle and outer cap. The inner cover should not leak out.

(2) Outer cover: The outer cover should be straight, smooth, free from cracks, burrs (burrs). The color of the outer cover should be uniform. The thread matching structure of the outer cover should be intact. The color of the outer cover with anodized aluminum or bronzing should be uniform. The outer cover of the clamshell type should be turned up flexibly, and the connection part shall not be broken. The fit between the cap and the bottle should be tight, without slippage or looseness.

3. Bag:

No obvious wrinkles, scratches, air bubbles should be applied to the bag. The color of the bag should be uniform. The sealing of the bag should be firm, and there should be no openings, perforations, or leakage (paste). The composite bag should be firm and evenly coated.

4. Hose:

The body of the hose should be smooth, neat, uniform in thickness, without obvious scratches, and uniform in color. The sealing of the hose should be firm and correct, and there should be no openings or wrinkles (except for the normal indentation of the mold). The cover of the hose shall meet the requirements of 5.3. The composite membrane of the hose should not float.

5. Box:

The surface of the box should be smooth and straight, and there should be no obvious scratches, burrs (burrs), severe collapse and damage. The tightness of the opening of the box should be suitable. When taking the flower box, do not peel it off with your fingers, so as to pinch the edge of the lid, and the bottom does not fall off. The mirror inside the box, the contents and the box should be firmly pasted, the mirror image should be good, and there should be no scratches or damage to the bottom.

6. Spray can

The tank body is flat, no rust spots, smooth welding seam, no obvious scratches, concave tank phenomenon, and the color should be uniform. The roll mouth of the spray can should be smooth and free of wrinkles, cracks and deformation. The lid of the spray can shall meet the requirements of 5.3.2.

7. Ingot tube

The tube body of the ingot tube should be straight, smooth, free of cracks, burrs (burrs), no obvious scratches, and uniform color. The components of the ingot tube should be tight and appropriate to ensure that the contents can be screwed out or pushed out normally.

8. Cosmetic pencil

The barrel and sleeve of the makeup pen should be smooth, straight, glue-free, and the paint film should not crack. The barrel of the makeup pen and the pen cover should be tight and tight. The color of the makeup pen should be uniform.

9. Nozzle

The nozzle should be upright, clean and free from damage and cracks. The assembly parts of the nozzle should be intact to ensure the smooth flow of spray at night.

10. Printing and labeling

The patterns and handwriting printed on cosmetics packaging should be neat, clear, not easy to fall off, and uniform in color. The labels of cosmetic packaging should not be mis-posted, missed, or upside down, and the paste should be firm. The labeling requirements shall be in accordance with the provisions of GB 5296.3.

11. Outer box

(1) Flower box: The flower box should be packaged tightly with the middle box. The flower box should be clean, straight and flat, and the box cover should be well covered, without wrinkles, missing edges, or missing corners. The bonding part of the flower box should be firmly pasted, without traces of pasting, cracking and mutual adhesion. The product has no wrong installation, missing installation, or upside-down installation.

(2) Medium box: The medium box should be tightly packaged with the flower box. The middle box should be clean, straight and flat, and the box cover should be closed. The bonding part of the middle box should be firmly pasted, without traces of pasting, cracking and mutual adhesion. The product has no wrong installation, missing installation, or upside-down installation. The label of the middle box shall be correct, clean and complete, and shall indicate the product name, specification, quantity of the box and the name of the producer as required.

(3) Plastic seal: The plastic seal should be adhered firmly without cracking. The plastic sealing surface should be clean and free from damage. There is no wrong installation, missing installation, or upside-down installation in the plastic package.

(4) Transport packaging: The transport packaging should be neat, upright, smooth, and tightly sealed. The product has no wrong installation, missing installation, or upside-down installation. The signs of the transportation package should be clear, complete, and in an appropriate location. The product name, manufacturer’s name and address, net content, product quantity, FCL quality (gross weight), volume, production date and shelf life or production batch number and deadline should be indicated as needed. Use date. The pictorial signs in GB/T 191 should be selected as required.